60 Technik
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- ja (33)
Gehört zur Bibliographie
- nein (33)
Schlagworte
- Elektromobilität (3)
- Rapid Prototyping <Fertigung> (3)
- additive manufacturing (3)
- 3D-Druck (2)
- Biokatalyse (2)
- Biotechnik (2)
- CO2 (2)
- Dach (2)
- Elektrode (2)
- Elektrofahrzeug (2)
In this paper two simple synthetic aperture radar (SAR) methods are applied on data from a 24 GHz FMCW radar implemented on a linear drive for educational purposes. The data of near and far range measurements are evaluated using two different SAR signal processing algorithms featuring 2D-FFT and frequency back projection (FBP) method (Moreira et al., 2013). A comparison of these two algorithms is performed concerning runtime, image pixel size, azimuth and range resolution. The far range measurements are executed in a range of 60 to 135 m by monitoring cars in a parking lot. The near range measurement from 0 to 5 m are realised in a measuring chamber equipped with absorber foam and nearly ideal targets like corner reflectors. The comparison of 2D-FFT and FBP algorithm shows that both deliver good and similar results for the far range measurements but the runtime of the FBP algorithm is up to 150 times longer as the 2D-FFT runtime. In the near range measurements the FBP algorithm displays a very good azimuth resolution and targets which are very close to each other can be separated easily. In contrast to that the 2D-FFT algorithm has a lower azimuth resolution in the near range, thus targets which are very close to each other, merge together and cannot be separated.
Geometrieerzeugung von Evolventenzahntrieben: Profilverschobene schrägverzahnte Stirnzahnräder
(2022)
In dieser Arbeit wird die Zahnradgeometrie von Stirnrädern berechnet und formatiert, um sie in ein CAD-Programm zu übertragen. Dabei werden die Konturen der Evolvente und der Trochoide nach den gleichen Regel wie bei der Herstellung durch Wälzfräsen erzeugt. Der Anwender hat die Möglichkeit die Haupteigenschaften wie Modul, Zahnkopfspiel und Eckenverrundung einzugeben. Zusätzlich können auch schrägverzahnte, profilverschobene Stirnräder mit Hochverzahnung und Kopfkürzung erzeugt werden.
Per Datenausgabe werden die Koordinaten gespeichert und durch ein Makro in das CAD-Programm übertragen. Aus den beiden Konturzügen wird der 3D-Körper durch Austragen entlang der Helix erzeugt.
Zur Weiterverarbeitung wird die Zahnradgeometrie nach manueller Tesselierung in ein universales Dateiformat exportiert.
In this paper, the mechanical damage behavior is investigated based on the characteristic roughness on the surface and the orientation of superficial structures. The main goal is to explore the surface roughness on mechanically loaded copper conductors as a lifetime indicator. For this purpose, copper conductors are mechanically stressed in accordance with EN 50,396 and then examined metallographically and microscopically. The microstructure examination shows that the roughness is caused by material extrusion and cracks due to work hardening in the surface area. Using confocal microscopy, it is shown for the first time that significant formation of surface roughness takes place over the service life of copper conductors. The roughness increases monotonically, but not linearly with number of cycles, due to internal microstructural processes and can be divided into three sections. First inspections of the conductor surface over lifetime show a correlation between the intensity of structures orientated 45° to the loading direction and the roughness. This phenomenon, already known from microscopic slip lines, is thus also evident in macroscopic roughness formation and is well founded by the research theory on material extrusion along dislocation lines. In summary, a lifetime determination is possible based on its developing roughness which enables the utilization as a sensor element.