60 Technik
Filtern
Erscheinungsjahr
Dokumenttyp
Volltext vorhanden
- ja (33)
Gehört zur Bibliographie
- nein (33)
Schlagworte
- Elektromobilität (3)
- Rapid Prototyping <Fertigung> (3)
- additive manufacturing (3)
- 3D-Druck (2)
- Biokatalyse (2)
- Biotechnik (2)
- CO2 (2)
- Dach (2)
- Elektrode (2)
- Elektrofahrzeug (2)
Background: Electric vehicles have been identified as being a key technology in reducing future emissions and energy consumption in the mobility sector. The focus of this article is to review and assess the energy efficiency and the environmental impact of battery electric cars (BEV), which is the only technical alternative on the market available today to vehicles with internal combustion engine (ICEV). Electricity onboard a car can be provided either by a battery or a fuel cell (FCV). The technical structure of BEV is described, clarifying that it is relatively simple compared to ICEV. Following that, ICEV can be ‘e-converted’ by experienced personnel. Such an e-conversion project generated reality-close data reported here.
Results: Practicability of today's BEV is discussed, revealing that particularly small-size BEVs are useful. This article reports on an e-conversion of a used Smart. Measurements on this car, prior and after conversion, confirmed a fourfold energy efficiency advantage of BEV over ICEV, as supposed in literature. Preliminary energy efficiency data of FCV are reviewed being only slightly lower compared to BEV. However, well-to-wheel efficiency suffers from 47% to 63% energy loss during hydrogen production. With respect to energy efficiency, BEVs are found to represent the only alternative to ICEV. This, however, is only true if the electricity is provided by very efficient power plants or better by renewable energy production. Literature data on energy consumption and greenhouse gas (GHG) emission by ICEV compared to BEV suffer from a 25% underestimation of ICEV-standardized driving cycle numbers in relation to street conditions so far. Literature data available for BEV, on the other hand, were mostly modeled and based on relatively heavy BEV as well as driving conditions, which do not represent the most useful field of BEV operation. Literature data have been compared with measurements based on the converted Smart, revealing a distinct GHG emissions advantage due to the German electricity net conditions, which can be considerably extended by charging electricity from renewable sources. Life cycle carbon footprint of BEV is reviewed based on literature data with emphasis on lithium-ion batteries. Battery life cycle assessment (LCA) data available in literature, so far, vary significantly by a factor of up to 5.6 depending on LCA methodology approach, but also with respect to the battery chemistry. Carbon footprint over 100,000 km calculated for the converted 10-year-old Smart exhibits a possible reduction of over 80% in comparison to the Smart with internal combustion engine.
Conclusion: Findings of the article confirm that the electric car can serve as a suitable instrument towards a much more sustainable future in mobility. This is particularly true for small-size BEV, which is underrepresented in LCA literature data so far. While CO2-LCA of BEV seems to be relatively well known apart from the battery, life cycle impact of BEV in categories other than the global warming potential reveals a complex and still incomplete picture. Since technology of the electric car is of limited complexity with the exception of the battery, used cars can also be converted from combustion to electric. This way, it seems possible to reduce CO2-equivalent emissions by 80% (factor 5 efficiency improvement).
Background: As electric kick scooters, three-wheelers, and passenger cars enter the streets, efficiency trade-offs across vehicle types gain practical relevance for consumers and policy makers. Here, we compile a comprehensive dataset of 428 electric vehicles, including seven vehicle types and information on certified and real-world energy consumption. Regression analysis is applied to quantify trade-offs between energy consumption and other vehicle attributes.
Results: Certified and real-world energy consumption of electric vehicles increase by 60% and 40%, respectively, with each doubling of vehicle mass, but only by 5% with each doubling of rated motor power. These findings hold roughly also for passenger cars whose energy consumption tends to increase 0.6 ± 0.1 kWh/100 km with each 100 kg of vehicle mass. Battery capacity and vehicle mass are closely related. A 10 kWh increase in battery capacity increases the mass of electric cars by 15 kg, their drive range by 40–50 km, and their energy consumption by 0.7–1.0 kWh/100 km. Mass-produced state-of-the-art electric passenger cars are 2.1 ± 0.8 kWh/100 km more efficient than first-generation vehicles, produced at small scale.
Conclusion: Efficiency trade-offs in electric vehicles differ from those in conventional cars—the latter showing a strong dependency of fuel consumption on rated engine power. Mass-related efficiency trade-offs in electric vehicles are large and could be tapped by stimulating mode shift from passenger cars to light electric road vehicles. Electric passenger cars still offer potentials for further efficiency improvements. These could be exploited through a dedicated energy label with battery capacity as utility parameter.
In this paper two simple synthetic aperture radar (SAR) methods are applied on data from a 24 GHz FMCW radar implemented on a linear drive for educational purposes. The data of near and far range measurements are evaluated using two different SAR signal processing algorithms featuring 2D-FFT and frequency back projection (FBP) method (Moreira et al., 2013). A comparison of these two algorithms is performed concerning runtime, image pixel size, azimuth and range resolution. The far range measurements are executed in a range of 60 to 135 m by monitoring cars in a parking lot. The near range measurement from 0 to 5 m are realised in a measuring chamber equipped with absorber foam and nearly ideal targets like corner reflectors. The comparison of 2D-FFT and FBP algorithm shows that both deliver good and similar results for the far range measurements but the runtime of the FBP algorithm is up to 150 times longer as the 2D-FFT runtime. In the near range measurements the FBP algorithm displays a very good azimuth resolution and targets which are very close to each other can be separated easily. In contrast to that the 2D-FFT algorithm has a lower azimuth resolution in the near range, thus targets which are very close to each other, merge together and cannot be separated.
Geometrieerzeugung von Evolventenzahntrieben: Profilverschobene schrägverzahnte Stirnzahnräder
(2022)
In dieser Arbeit wird die Zahnradgeometrie von Stirnrädern berechnet und formatiert, um sie in ein CAD-Programm zu übertragen. Dabei werden die Konturen der Evolvente und der Trochoide nach den gleichen Regel wie bei der Herstellung durch Wälzfräsen erzeugt. Der Anwender hat die Möglichkeit die Haupteigenschaften wie Modul, Zahnkopfspiel und Eckenverrundung einzugeben. Zusätzlich können auch schrägverzahnte, profilverschobene Stirnräder mit Hochverzahnung und Kopfkürzung erzeugt werden.
Per Datenausgabe werden die Koordinaten gespeichert und durch ein Makro in das CAD-Programm übertragen. Aus den beiden Konturzügen wird der 3D-Körper durch Austragen entlang der Helix erzeugt.
Zur Weiterverarbeitung wird die Zahnradgeometrie nach manueller Tesselierung in ein universales Dateiformat exportiert.
Electric drive systems are increasingly used in automobiles. However, the combination of comfort, dynamics and safety requirements places high demands on the torque accuracy. The complex interplay of battery, inverter and electrical machine causes a lot of system uncertainties based on parameter fluctuations and measurement errors that influence the system performance. In this paper these influences on the closed loop torque control are analyzed and quantified using a variance based sensitivity analysis. The method enables to connect the variance of the torque accuracy with the parameter uncertainties causing this variance. Moreover, it quantifies the influences of the parameters independent of the complexity of the analyzed system. In addition, two methods to ensure convergence of the estimated variance based sensitivity measures are proposed. The results of the analysis are presented for 19 static working points of an battery electric drive system.
Since operational managers often monitor large numbers of wind turbines (WTs), they depend on a toolset to provide them with highly condensed information to identify and prioritize low performing WTs or schedule preventive maintenance measures. Power curves are a frequently used tool to assess the performance of WTs. The power curve health value (HV) used in this work is supposed to detect power curve anomalies since small deviations in the power curve are not easy to identify. It evaluates deviations in the linear region of power curves by performing a principal component analysis. To calculate the HV, the standard deviation in direction of the second principal component of a reference data set is compared to the standard deviation of a combined data set consisting of the reference data and data of the evaluated period. This article examines the applicability of this HV for different purposes as well as its sensitivities and provides a modified HV approach to make it more robust and suitable for heterogeneous data sets. The modified HV was tested based on ENGIE's open data wind farm and data of on- and offshore WTs from the WInD-Pool. It proved to detect anomalies in the linear region of the power curve in a reliable and sensitive manner and was also eligible to detect long term power curve degradation. Also, about 7 % of all corrective maintenance measures were preceded by high HVs with a median alarm horizon of three days. Overall, the HV proved to be a promising tool for various applications.
This paper presents a feasibility study for the production of recycled glycol modified polyethylene terephthalate (PETG) material for additive manufacturing. Past studies showed a variety of results for the recycling of 3D-printing material, therefore the precise effect on the material properties is not completely clear. For this work, PETG waste of the same grade was recycled once and further processed into 3D printing filament. The study compares three blend ratios between purchased plastic pellets and recycled pellets to determine the degradation effect of one recycling cycle and possible blend ratios to counter these effects. Furthermore, the results include a commercially available filament. The comparison uses the filament diameter, the dimensional accuracy of the printed test specimen and mechanical properties as quality criteria. The study shows that the recycled material has a minor decrease concerning the tensile strength and Young’s modulus.
As productive biofilms are increasingly gaining interest in research, the quantitative monitoring of biofilm formation on- or offline for the process remains a challenge. Optical coherence tomography (OCT) is a fast and often used method for scanning biofilms, but it has difficulty scanning through more dense optical materials. X-ray microtomography (μCT) can measure biofilms in most geometries but is very time-consuming. By combining both methods for the first time, the weaknesses of both methods could be compensated. The phototrophic cyanobacterium Tolypothrix distorta was cultured in a moving bed photobioreactor inside a biocarrier with a semi-enclosed geometry. An automated workflow was developed to process µCT scans of the biocarriers. This allowed quantification of biomass volume and biofilm-coverage on the biocarrier, both globally and spatially resolved. At the beginning of the cultivation, a growth limitation was detected in the outer region of the carrier, presumably due to shear stress. In the later phase, light limitations could be found inside the biocarrier. µCT data and biofilm thicknesses measured by OCT displayed good correlation. The latter could therefore be used to rapidly measure the biofilm formation in a process. The methods presented here can help gain a deeper understanding of biofilms inside a process and detect any limitations.
Passenger cars in Europe have become both heavier and more powerful over the past decades. This trend has increased vehicle utility but it might have also offset technical improvements in powertrain efficiency. Here, we analyze efficiency trade-offs and CO2 emissions for three popular compact cars in Germany. We find that mass, power, and front area of model variants has increased by 66%, 147%, and 22%, respectively between 1980 and 2018. In the same period, fuel consumption decreased 14% for gasoline models but it increased 9% for diesel models. However, if vehicle mass, power, and front area had remained at 1980 levels, technical efficiency improvements would have decreased the fuel consumption of gasoline and diesel models by 23% and 24%, respectively. The related efficiency trade-offs amount to 24 g CO2/km or 13% of the current fuel consumption for gasoline models and 40 g CO2/km or 25% of the current fuel consumption for diesel models. These findings suggest that about half of the technical efficiency improvements in gasoline models and all of the technical efficiency improvements in diesel models are offset through other vehicle attributes. By accounting for the observed efficiency trade-offs, climate policy could become more effective.
Electrical stimulation is used for example to treat neuronal disorders and depression with deep brain stimulation or transcranial electrical stimulation. Depending on the application, different electrodes are used and thus different electrical characteristics exist, which have to be handled by the stimulator. Without a measuring device the user would have to rely on the stimulator being able to deliver the needed stimulation signal. Therefore, the objective of this paper is to present a method to increase the level of confidence with characterization and modelling of the electrical behavior by using the example of one channel of our stimulation device for experimental use. In several simulation studies with an electrode model with values in a typical range for cortical applications the influence of the load onto the stimulator and the possibility to pre-estimate measuring signals in complex networks are shown.