FB Umweltplanung/-technik (UCB)
Filtern
Dokumenttyp
Sprache
- Englisch (4)
Volltext vorhanden
- ja (4)
Gehört zur Bibliographie
- nein (4) (entfernen)
Schlagworte
- Rapid Prototyping <Fertigung> (4) (entfernen)
Institut
The number of additive manufacturing methods and materials is growing rapidly, leaving gaps in the knowledge of specific material properties. A relatively recent addition is the metal-filled filament to be printed similarly to the fused filament fabrication (FFF) technology used for plastic materials, but with additional debinding and sintering steps. While tensile, bending, and shear properties of metals manufactured this way have been studied thoroughly, their fatigue properties remain unexplored. Thus, the paper aims to determine the tensile, fatigue, and impact strengths of Markforged 17-4 PH and BASF Ultrafuse 316L stainless steel to answer whether the metal FFF can be used for structural parts safely with the current state of technology. They are compared to two 316L variants manufactured via selective laser melting (SLM) and literature results. For extrusion-based additive manufacturing methods, a significant decrease in tensile and fatigue strength is observed compared to specimens manufactured via SLM. Defects created during the extrusion and by the pathing scheme, causing a rough surface and internal voids to act as local stress risers, handle the strength decrease. The findings cast doubt on whether the metal FFF technique can be safely used for structural components; therefore, further developments are needed to reduce internal material defects.
Additive manufacturing is an essential tool in innovative production processes. The extended degrees of freedom offer much potential in usage, construction, and product design. Rising raw material and energy costs, constantly increasing environmental requirements, and the increasing demand for resource-saving products represent a paradigm shift in classic production processes.
In addition to the purely energetic evaluation, developing energy models is a method to determine energy consumption and reduce it in the long term. The specific energy consumption model, also known as the SEC model, allows a quick estimation of energy consumption by multiplying the SEC with a unit like the mass of the workpiece, the manufacturing time, or the exposed area. Here, high dependence on the used machine, the considered peripheral devices, and the geometry are noticeable.
Previous studies, such as those by Kellens et al. and Baumers et al., have laid the basis for understanding the energy demands of PBF-LB/M processes. Various energy models have subsequently been proposed, including those by Paul and Anand, Yi et al., Lv et al., and Hui et al. These models are often limited by their specificity to sub-processes or subsystems. This results in limitations in their applicability to other manufacturing machines or inaccuracies in energy consumption predictions. The simulation accuracy ACC is mostly in the range of 90% with the limitation of small sample sizes. Moreover, nearly, all these models rely heavily on process time information, making the accuracy of their simulations largely dependent on the quality of the underlying time model.
In the following study, two manufacturing machines of the PBF-LB/M process are analyzed and compared with other studies. The aim is to analyze the power and resource consumption to use these data to build an improved energy model with a high accuracy, which can be used as an additional parameter in the adapted design methodology. Furthermore, potential savings are derived from the load curves.
Productive biofilms are gaining growing interest in research due to their potential of producing valuable compounds and bioactive substances such as antibiotics. This is supported by recent developments in biofilm photobioreactors that established the controlled phototrophic cultivation of algae and cyanobacteria. Cultivation of biofilms can be challenging due to the need of surfaces for biofilm adhesion. The total production of biomass, and thus production of e.g. bioactive substances, within the bioreactor volume highly depends on the available cultivation surface. To achieve an enlargement of surface area for biofilm photobioreactors, biocarriers can be implemented in the cultivation. Thereby, material properties and design of the biocarriers are important for initial biofilm formation and growth of cyanobacteria. In this study, special biocarriers were designed and additively manufactured to investigate different polymeric materials and surface designs regarding biofilm adhesion of the terrestrial cyanobacterium Nostoc flagelliforme (CCAP 1453/33). Properties of 3D-printed materials were characterized by determination of wettability, surface roughness, and density. To evaluate the influence of wettability on biofilm formation, material properties were specifically modified by gas-phase fluorination and biofilm formation was analyzed on biocarriers with basic and optimized geometry in shaking flask cultivation. We found that different polymeric materials revealed no significant differences in wettability and with identical surface design no significant effect on biomass adhesion was observed. However, materials treated with fluorination as well as optimized biocarrier design showed improved wettability and an increase in biomass adhesion per biocarrier surface.
This paper presents a feasibility study for the production of recycled glycol modified polyethylene terephthalate (PETG) material for additive manufacturing. Past studies showed a variety of results for the recycling of 3D-printing material, therefore the precise effect on the material properties is not completely clear. For this work, PETG waste of the same grade was recycled once and further processed into 3D printing filament. The study compares three blend ratios between purchased plastic pellets and recycled pellets to determine the degradation effect of one recycling cycle and possible blend ratios to counter these effects. Furthermore, the results include a commercially available filament. The comparison uses the filament diameter, the dimensional accuracy of the printed test specimen and mechanical properties as quality criteria. The study shows that the recycled material has a minor decrease concerning the tensile strength and Young’s modulus.